Engraving 1m Width Factory Manufacture Digital Vinyl Printing Machines H1180 Model Vinyl Banner Printing Plotter
Jinan Yuntu CNC Equipment Co., Ltd.- After-sales Service：Long-Term Support for The Software and Machine Mai
- Warranty：The Whole Machine , Parts Are Guaranteed for One Y
- Classification：Single-blade Cutter
- Driven Type：Electric
- Type：Industrial Cutter
- Blade Material：Stainless Steel
Base Info
- Model NO.：H1180
- Computerized：Computerized
- Cache Capacity：4MB
- Cutter Pressure：0-500g
- Cutting Speed：0-800mm,S
- Cutting Length：Unlimited
- Product Name：Plotter Cutter
- Voltage：110V,240V
- Paper Feed Width：1100mm
- Cutting Width：1000mm
- Transport Package：Carton
- Specification：long130CM*wide22CM*high14CM weight: 16.1KG
- Trademark：yuntu
- Origin：Jinan City, Shandong Province, China
- HS Code：3701100000
- Production Capacity：50000
Description
TitleProducts Description29.9KG 
Q:Why is the pattern deformed or incomplete? 1. More pressure or too long blade tip or too dirty platen or too soft stickiness,
all of these factors can cause more resistance to the two faces of paper and make it fall behind the roller rotating, thus result in
deformed pattern. 2. The software setting isn't proper. (The tool compensation value is too big) 3. The carriage belt is too loose,
or the metal roller can't exactly follow the motor running. 4. The motor doesn't run all the steps. 5. The pattern is normal but not
complete, this may be resulted from too small tool compensation value.
Q:Why does the machine plot abnormally? 1. Software setting is not matched to the machine, so you must adopt proper
commands set or set proper tool compensation value. 2. The plotting software is suddenly broken up. 3. Plotting software has
been damaged or there is virus in computer.
Q:Why does the paper run deviation? 1. The stickiness isn't placed right. 2. The platen is too dirty so that the resistance from
two sides can't be balanced when the paper is moving. 3. The pinch rollers have been deformed or don't match to each other.
4. The pressure of the pinch roller is a little smaller and the paper is very sensitive to the external force. 5. The balance of the
stickiness weight isn't very good.
Q:Why some parts of letters are missing? 1. The vinyl is too heavy or too tightly wrapped. Metal roller might be soiled by
some foreign substance or by vinyl chips. 2. Cutting speed is too fast, cutting force is too great, or cutter tip is too long. 3.
Synchromesh belt is too tight, or pinch roller is under too much pressure. 4. Metal roller is faulty. Contact local distributor for
repairs and replacement. Q:Why different letters on the same line are cut to different depths? 1. Cutter holder is not tightly
attached. It should be tightened. 2. Cutter blade is not tightly set in the holder.
Q:Why letters appear to have ripples? 1. Cutting speed is too fast. Except for cutting large letters, speed should not exceed
80mm/s. 2. Cutting blade is of poor quality, or it has been damaged. Replace it. 3. Cutter holder is not tightly installed. Tighten
screw. Cutting small letters When cutting small letters, cutting speed and force should be adjusted to the lowest setting. Similarly
cutter tip should be adjusted to as short as possible. Cutting large letters Cutting speed and force may be increased to higher
settings. When cutting large letters Sharp Angle in Artcut software may be ignored.
Q:Why is the pattern deformed or incomplete? 1. More pressure or too long blade tip or too dirty platen or too soft stickiness,
all of these factors can cause more resistance to the two faces of paper and make it fall behind the roller rotating, thus result in
deformed pattern. 2. The software setting isn't proper. (The tool compensation value is too big) 3. The carriage belt is too loose,
or the metal roller can't exactly follow the motor running. 4. The motor doesn't run all the steps. 5. The pattern is normal but not
complete, this may be resulted from too small tool compensation value.
Q:Why does the machine plot abnormally? 1. Software setting is not matched to the machine, so you must adopt proper
commands set or set proper tool compensation value. 2. The plotting software is suddenly broken up. 3. Plotting software has
been damaged or there is virus in computer.
Q:Why does the paper run deviation? 1. The stickiness isn't placed right. 2. The platen is too dirty so that the resistance from
two sides can't be balanced when the paper is moving. 3. The pinch rollers have been deformed or don't match to each other.
4. The pressure of the pinch roller is a little smaller and the paper is very sensitive to the external force. 5. The balance of the
stickiness weight isn't very good.
Q:Why some parts of letters are missing? 1. The vinyl is too heavy or too tightly wrapped. Metal roller might be soiled by
some foreign substance or by vinyl chips. 2. Cutting speed is too fast, cutting force is too great, or cutter tip is too long. 3.
Synchromesh belt is too tight, or pinch roller is under too much pressure. 4. Metal roller is faulty. Contact local distributor for
repairs and replacement. Q:Why different letters on the same line are cut to different depths? 1. Cutter holder is not tightly
attached. It should be tightened. 2. Cutter blade is not tightly set in the holder.
Q:Why letters appear to have ripples? 1. Cutting speed is too fast. Except for cutting large letters, speed should not exceed
80mm/s. 2. Cutting blade is of poor quality, or it has been damaged. Replace it. 3. Cutter holder is not tightly installed. Tighten
screw. Cutting small letters When cutting small letters, cutting speed and force should be adjusted to the lowest setting. Similarly
cutter tip should be adjusted to as short as possible. Cutting large letters Cutting speed and force may be increased to higher
settings. When cutting large letters Sharp Angle in Artcut software may be ignored.